资源描述：
BS EN 14636-12009 ICS 23.040.50; 93.030 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Plastics piping systems for non-pressure drainage and sewerage Polyester resin concrete PRC Part 1 Pipes and fittings with flexible joints Licensed Copy athen reading, Reading University Library, 24/01/2010 0205, Uncontrolled Copy, c BSI This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2010. BSI 2009 ISBN 978 0 580 53799 8 Amendments/corrigenda issued since publication DateComments BS EN 14636-12009 National foreword This British Standard is the UK implementation of EN 14636-12009. The UK participation in its preparation was entrusted to Technical Committee PRI/88/2, Plastics piping for pressure applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed Copy athen reading, Reading University Library, 24/01/2010 0205, Uncontrolled Copy, c BSI BS EN 14636-12009 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14636-1 November 2009 ICS 23.040.50; 93.030 English Version Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete PRC - Part 1 Pipes and fittings with flexible joints Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement sans pression - Bton de rsine polyester PRC - Partie 1 Tubes et raccords avec assemblages flexibles Kunststoff-Rohrleitungssysteme fr drucklos betriebene Abwasserkanle und -leitungen - Gefllte Polyesterharzstoffe PRC - Teil 1 Rohre und stcke mit flexiblen Verbindungen This European Standard was approved by CEN on 5 October 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions English, French, German. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any and by any means reserved worldwide for CEN national Members. Ref. No. EN 14636-12009 E Licensed Copy athen reading, Reading University Library, 24/01/2010 0205, Uncontrolled Copy, c BSI BS EN 14636-12009 EN 14636-12009 E 2 Contents Page Foreword ................................................................................................................................................ 5 1Scope .............................................................................................................................................. 6 2Normative references ................................................................................................................... 6 3Terms, definitions, symbols and abbreviations ........................................................................ 7 3.1Terms and definitions ................................................................................................................ 7 3.2Symbols and abbreviations .................................................................................................... 10 4General requirements ................................................................................................................. 14 4.1Materials .................................................................................................................................... 14 4.2Appearance ............................................................................................................................... 14 4.3Reference conditions for testing ............................................................................................ 14 4.4Joints ......................................................................................................................................... 15 5Pipes ............................................................................................................................................. 16 5.1Classification ............................................................................................................................ 16 5.2Designation ............................................................................................................................... 16 5.3Geometrical characteristics .................................................................................................... 17 5.4Mechanical characteristics ..................................................................................................... 26 5.5Marking of pipes....................................................................................................................... 30 6Fittings ......................................................................................................................................... 30 6.1General ...................................................................................................................................... 30 6.2Bends ........................................................................................................................................ 31 6.3Branches ................................................................................................................................... 34 6.4Marking of fittings .................................................................................................................... 36 7Joint perance ....................................................................................................................... 36 7.1General ...................................................................................................................................... 36 7.2Requirements ........................................................................................................................... 36 8Dangerous substances ............................................................................................................... 39 9Manufacturers installation recommendations ........................................................................ 39 10uation of conity ............................................................................................................ 39 10.1General ...................................................................................................................................... 39 10.2Initial type testing..................................................................................................................... 40 10.3Factory production control FPC .......................................................................................... 43 10.4One-off products, pre-production products e.g. prototypes and products produced in very low quantities .............................................................................................................................. 46 Annex A normative Determination of a pipe’s crushing strength and ring bending tensile strength using a pipe test piece ........................................................................................................ 47 A.1Scope ........................................................................................................................................ 47 A.2Principle .................................................................................................................................... 47 A.3Apparatus ................................................................................................................................. 47 A.4Test pieces ................................................................................................................................ 51 A.5Procedure ................................................................................................................................. 51 A.6Calculations .............................................................................................................................. 51 A.7Test report ................................................................................................................................ 54 Licensed Copy athen reading, Reading University Library, 24/01/2010 0205, Uncontrolled Copy, c BSI BS EN 14636-12009 EN 14636-12009 E 3 Annex B normative Determination of a pipe’s crushing strength or the ring bending tensile strength using test pieces sawn from a pipe ................................................................................... 55 B.1Scope ......................................................................................................................................... 55 B.2Principle ..................................................................................................................................... 55 B.3Apparatus .................................................................................................................................. 55 B.4Test piece .................................................................................................................................. 56 B.5Test procedure .......................................................................................................................... 57 B.6Calculations .............................................................................................................................. 59 B.7Test report ................................................................................................................................. 60 Annex C normative Assessment of longitudinal bending moment resistance BMR ............. 61 C.1Scope ......................................................................................................................................... 61 C.2Principle ..................................................................................................................................... 61 C.3Apparatus .................................................................................................................................. 61 C.4Procedure .................................................................................................................................. 63 C.5Calculations .............................................................................................................................. 64 C.6Test report ................................................................................................................................. 65 Annex D normative Determination of the compressive strength of polyester resin concrete PRC using test pieces which are cut from a pipe .......................................................................... 66 D.1Scope ......................................................................................................................................... 66 D.2Principle ..................................................................................................................................... 66 D.3Apparatus .................................................................................................................................. 66 D.4Test pieces ................................................................................................................................ 68 D.5Procedure .................................................................................................................................. 68 D.6Calculations .............................................................................................................................. 68 D.7Test report ................................................................................................................................. 68 Annex E normative Determination of the fatigue strength of a pipe under cyclic loading ...... 69 E.1Scope ......................................................................................................................................... 69 E.2Principle ..................................................................................................................................... 69 E.3Apparatus .................................................................................................................................. 69 E.4Test pieces ................................................................................................................................ 70 E.5Procedure .................................................................................................................................. 71 E.6Calculations .............................................................................................................................. 71 E.7Test report ................................................................................................................................. 72 Annex F normative Assessment of the leak-tightness of a pipe and its joints under short term exposure to internal water pressure ................................................................................................. 74 F.1Scope ......................................................................................................................................... 74 F.2Principle ..................................................................................................................................... 74 F.3Apparatus .................................................................................................................................. 74 F.4Procedure ...........
展开阅读全文
