资源描述：
BRITISH STANDARD BS EN 1504-72006 Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 7 Reinforcement corrosion protection The European Standard EN 1504-72006 has the status of a British Standard ICS 91.080.40 BS EN 1504-72006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006 ISBN 0 580 49247 8 National foreword This British Standard was published by BSI. It is the UK implementation of EN 1504-72006. The UK participation in its preparation was entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/8, Protection and repair of concrete structures. A list of organizations represented on B/517/8 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1504-7 August 2006 ICS 91.080.40 English Version Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and uation of conity - Part 7 Reinforcement corrosion protection Produits et systmes pour la protection et la rparation des structures en bton - Dfinitions, exigences, matrise de la qualit et valuation de la conit - Partie 7 Protection contre la corrosion des armatures Produkte und Systeme fr den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualittsberwachung und Beurteilung der Konitt - Teil 7 Korrosionsschutz der Bewehrung This European Standard was approved by CEN on 19 June 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions English, French, German. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any and by any means reserved worldwide for CEN national Members. Ref. No. EN 1504-72006 E w w w . b z f x w . c o m EN 1504-72006 E 2 Contents Page 1 Scope ......................................................................................................................................................5 2 Normative references............................................................................................................................5 3 Terms and definitions ...........................................................................................................................6 4 Perance characteristics for intended uses.................................................................................6 5 Requirements.........................................................................................................................................7 6 Sampling.................................................................................................................................................8 7 uation of conity.......................................................................................................................8 8 Marking and labelling............................................................................................................................9 Annex A inative Minimum frequency of testing for factory production control.............................10 Annex B inative Release of dangerous substances..........................................................................11 Annex ZA inative Clauses of this European Standard addressing the provisions of the EU Construction Products Directive........................................................................................................12 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-72006 E 3 Foreword This document EN 1504-72006 has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2007, and conflicting national standards shall be withdrawn at the latest by December 2008. It has been developed by sub-committee 8 “Protection and repairs of concrete structures“ Secretariat AFNOR. This Part of EN 1504 does not supersede any other European Standard. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU Construction Products Directive 89/106/EC. For the relationship with the EU Directive, see inative Annex ZA, which is an integral part of this document. This Part of EN 1504 includes an inative Annex A, dealing with minimum frequency of testing for factory production control. This Part of EN 1504 is one of the parts of this standard on products and systems for the repair and protection of concrete structures. The other parts are listed below EN 1504-1, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 1 Definitions. EN 1504-2, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 2 Surface protection systems for concrete. EN 1504-3, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 3 Structural and non-structural repair. EN 1504-4, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 4 Structural bonding. EN 1504-5, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 5 Concrete injection. prEN 1504-61, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 6 Anchoring of reinforcing steel bar. EN 1504-8, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 8 Quality control and uation of conity. 1 This document is in preparation. w w w . b z f x w . c o m EN 1504-72006 E 4 ENV 1504-92, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 9 General principles for the use of products and systems. EN 1504-10, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 10 Site application of products and systems and quality control of the works. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 2 ENV 1504-9 will have to be modified when adopted as EN according to finalisation of this European Standard. 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-72006 E 5 1 Scope This Part of EN 1504 specifies requirements for the identification and the perance including durability aspects of products and systems for active and barrier coatings for protection of existing uncoated steel reinforcement and embedded steel in concrete structures under repair. This standard does not cover products for corrosion protection of pre-stressing steels and stainless steels. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document including any amendments applies. EN 1015-4, s of test for mortar for masonry Part 4 Determination of consistence of fresh mortar by plunger penetration EN 1504-12005, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 1 Definitions EN 1504-82004, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 8 Quality control and uation of conity ENV 1504-91997, Products and systems for the protection and repair of concrete structures Definitions, Requirements, Quality control and uation of conity Part 9 General principles for the use of products and systems EN 1767, Products and systems for the protection and repair of concrete structures Test s Infrared analysis EN 1877-1, Products and systems for the protection and repair of concrete structures Test s Reactive functions related to epoxy resins Part 1 Determination of epoxy equivalent EN 1877-2, Products and systems for the protection and repair of concrete structures Test s Reactive functions related to epoxy resins Part 2 Determination of amine functions using the total basicity number EN 12614, Products and systems for the protection and repair of concrete structures Test s Determination of glass transition temperatures of polymers EN 13062, Products and systems for the protection and repair of concrete structure Test Determination of thixotropy of products for protection of reinforcement EN 15183 3 Products and systems for the protection and repair of concrete structures Test s Corrosion protection test EN 15184 3 Products and systems for the protection and repair of concrete structures Test s Shear adhesion of coated steel to concrete pull-out test 3 This document is in preparation. w w w . b z f x w . c o m EN 1504-72006 E 6 EN ISO 868, Plastics and ebonite Determination of indentation hardness by means of a durometer Shore hardness ISO 8682003 EN ISO 2811-1, Paints and varnishes Determination of density Part 1 Pyknometer ISO 2811- 11997 EN ISO 2811-2, Paints and varnishes Determination of density Part 2 Immersed body plummet ISO 2811-21997 EN ISO 3219, Plastics Polymers/resins in the liquid state or as emulsions or dispersions Determination of viscosity using a rotational viscometer with defined shear rate ISO 32191993 EN ISO 3251, Paints, varnishes and plastics Determination of non-volatile-matter content ISO 32512003 EN ISO 9514, Paints and varnishes - Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for testing ISO 95142005 EN ISO 11358, Plastics Thermogravimetry TG of polymers General principles ISO 113581997 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1504-12005, EN 1504-82004, ENV 1504-91997 and the following apply. 3.1 active coatings coatings, which contain electrochemically active pigments, which may function as inhibitors or which may provide localised cathodic protection NOTE Cement is considered to be an active pigment due to its alkalinity. 3.2 barrier coatings coatings which isolate the reinforcement from pore water in the surrounding cementitious matrix 4 Perance characteristics for intended uses Table 1 lists the perance characteristics of reinforcement corrosion protection products and systems, which are required for “all intended uses” or “for certain intended uses” according to the “principles” and “s” defined in ENV 1504-9. Perance characteristics which are required for “all intended uses” are marked g. All other perance characteristics which are marked 1 may be required for “certain intended uses”. Perance requirements are given in 5.2. 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-72006 E 7 Table 1 Perance characteristics for all and certain intended uses Intended uses Test s defined in Perance characteristics Active coating 11.1a Barrier coating 11.2a EN 15183 Corrosion protection g g EN 12614 Glass transition temperature 1 1 EN 15184 Shear adhesion coated steel to concrete 1 1 a in accordance with ENV 1504-9. 5 Requirements 5.1 Identification requirements The manufacturer shall undertake selected representative initial identification tests for the product or system as specified in Table 2. These tests may be used to confirm the composition of the product at any time. Acceptable tolerances are given in Table 2. The manufacturer shall hold the test records. Table 2 Identification test s and requirements Property Test Requirement/tolerance Components liquid Colour/general appearance Visual Uni and similar to the description pro- vided by the manufacturer Density Pyknometer Immersed body EN ISO 2811-1 EN ISO 2811-2 3 3 Infrared spectrum EN 1767 Confirmed by visual comparison Epoxy equivalenta E
展开阅读全文
