资源描述：
BRITISH STANDARD BS EN 1504-62006 Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 6 Anchoring of reinforcing steel bar The European Standard EN 1504-62006 has the status of a British Standard ICS 91.080.40 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI BS EN 1504-62006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September 2006 BSI 2006 ISBN 0 580 49246 X National foreword This British Standard was published by BSI. It is the UK implementation of EN 1504-62006. The UK participation in its preparation was entrusted by Technical Committee B/517, Concrete, to Subcommittee B/517/8, Protection and repair of concrete structures. A list of organizations represented on B/517/8 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments BSI 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1504-6 August 2006 ICS 91.080.40 English Version Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and uation of conity - Part 6 Anchoring of reinforcing steel bar Produits et systmes pour la protection et la rparation des structures en bton - Dfinitions, exigences, matrise de la qualit et valuation de la conit - Partie 6 Ancrage darmature Produkte und Systeme fr den Schutz und die Instandsetzung von Betontragwerken - Definitionen, Anforderungen, Qualittsberwachung und Beurteilung der Konitt - Teil 6 Verankerung von Bewehrungsstben This European Standard was approved by CEN on 19 July 2006. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions English, French, German. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre rue de Stassart, 36 B-1050 Brussels 2006 CENAll rights of exploitation in any and by any means reserved worldwide for CEN national Members. Ref. No. EN 1504-62006 E BSI w w w . b z f x w . c o m EN 1504-62006 E 2 Contents Page Foreword..............................................................................................................................................................3 1 Scope ......................................................................................................................................................5 2 Normative references............................................................................................................................5 3 Terms and definitions ...........................................................................................................................6 4 Perance characteristics for intended uses.................................................................................6 5 Requirements.........................................................................................................................................7 5.1 Identification requirements...................................................................................................................7 5.2 Perance requirements...................................................................................................................7 5.3 Release of dangerous substances.......................................................................................................8 5.4 Reaction to fire.......................................................................................................................................8 6 Sampling.................................................................................................................................................8 7 uation of conity.......................................................................................................................8 7.1 General....................................................................................................................................................8 7.2 Initial type testing ..................................................................................................................................8 7.3 Factory production control...................................................................................................................9 7.4 Assessment, surveillance and certification of factory production control inative..............9 8 Marking and labelling............................................................................................................................9 Annex A inative Minimum frequency of testing for factory production control...............................10 Annex B inative Release of dangerous substances............................................................................11 Annex ZA inative Clauses of this European Standard addressing the provisions of the EU Construction Products Directive........................................................................................................12 ZA1 Scope and relevant characteristics ...................................................................................................12 ZA.2 Attestation of conity....................................................................................................................14 ZA.3 CE marking and labelling....................................................................................................................19 BSI 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-62006 E 3 Foreword This document EN 1504-62006 has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2007, and conflicting national standards shall be withdrawn at the latest by December 2008. It has been developed by sub-committee 8 “Products and systems for the protection and repair of concrete structures“ Secretariat AFNOR. This Part of EN 1504 does not supersede any other European Standard. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU Construction Products Directive 89/106/EC. For the relationship with the EU Directive, see inative Annex ZA, which is an integral part of this document. This Part of EN 1504 includes an inative Annex A dealing with factory production control and an inative Annex B dealing with release of dangerous substances. This Part of this European Standard is one of the Parts of this standard on products and systems for the repair and protection of concrete structures. The other parts are listed below EN 1504-1, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity – Part 1 Definitions. EN 1504-2, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity – Part 2 Surface protection systems for concrete. EN 1504-3, Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and uation of conity - Part 3 Structural and non-structural repair. EN 1504-4, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity – Part 4 Structural bonding. EN 1504-5, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity – Part 5 Concrete injection. EN 1504-7, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity – Part 7 Reinforcement corrosion protection. EN 1504-8, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity – Part 8 Quality control and uation of conity. BSI w w w . b z f x w . c o m EN 1504-62006 E 4 ENV 1504-9 1, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity – Part 9 General principles for the use of products and systems. EN 1504-10, Products and systems for the protection and repair of concrete structures – Definitions, requirements, quality control and uation of conity - Part 10 Site application of products and systems and quality control of the works. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. 1 ENV 1504-9 will be modified when adopted as EN according to finalisation of this European Standard BSI 标准分享网 w w w .b z f x w .c o m 免费下载 w w w . b z f x w . c o m EN 1504-62006 E 5 1 Scope This Part of EN 1504 specifies requirements for the identification, perance including durability and safety of products and systems to be used for the anchoring of reinforcing steel rebar as used for structural strengthening to ensure the continuity of reinforced concrete structures. This Part of EN 1504 covers the fields of application in accordance with repair 4.2 of ENV 1504- 91997. NOTE It is assumed that a proper structural assessment of the structural elements to be subjected to repair is carried out by qualified engineers and that the choice of the products and systems to be used as well as the design are based on this assessment. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document including any amendments applies. EN 1015-17, s of test for mortar for masonry Part 17 Determination of water-soluble chloride content of fresh mortars EN 1504-12005, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 1 Definitions EN 1504-82004, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 8 Quality control and uation of conity ENV 1504-91997, Products and systems for the protection and repair of concrete structures Definitions, requirements, quality control and uation of conity Part 9 General principles for the use of products and systems prEN 1544, Products and systems for the protection and repair of concrete structures Test s Determination of creep under sustained tensile load for synthetic resin products PC for the anchoring of reinforcing bars EN 1767, Products and systems for the protection and repair of concrete structures Test s Infra- red analysis EN 1877-1, Products and systems for the protection and repair of concrete structures Test s Reactive functions related to epoxy resins Part 1 Determination of epoxy equivalent EN 1877-2, Products and systems for the protection and repair of concrete structures Test s Reactive functions related to epoxy resins Part 2 Determination of amine functions using the total basicity number prEN 1881, Products and systems for the protection and repair of concrete structures Test s Testing of anchoring products by the pull out EN 12190, Products and systems for the protection and repair of concrete structures Test s Determination of compressive strength of repair mortar EN 12192-1, Products and systems for the protection and repair of concrete structures Granulometry analysis Part 1 Test for dry components of premixed mortar BSI w w w . b z f x w . c o m EN 1504-62006 E 6 EN 12614, Products and systems for the protection and repair of concrete structures Test s Determination of glass transition temperatures of polymers EN 13294, Products and systems for the protection and repair of concrete structures Test s Determination of stiffening time EN 13395-2, Products and systems for the protection and repair of concrete structures Test s Determination of workability - Part 2 Test for flow of grout or mortar EN 13501-1, Fire classification of construction products and building elements Part 1 Classification using test data from reaction to fire tests EN ISO 9514, Paints and varnishes Determination of the pot life of multicomponent coating systems Preparation and conditioning of samples and guidelines for testing ISO 95142005 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1504-12005, EN 1504-82004, ENV 1504-91997 and the following apply. 3.1 anchoring product products based on hydraulic binders or synthetic resins or a mixture of these, installed at a fluid or paste consistency, to grout r
展开阅读全文
